Jabra Projector Accessories SP CEIL 012 User Manual

INSTALLATION MANUAL  
SP-CEIL-012  
InFocus Corporation  
27700B S.W. Parkway Ave.  
Wilsonville, OR 97070-9215  
1-800-294-6400  
IN-SPECEIL012.R2  
 
SP-CEIL-012  
Table of Contents  
Warning Statements............................................................................................................................................- 4 -  
Parts List .............................................................................................................................................................- 5 -  
Installation Tools ................................................................................................................................................- 5 -  
Ceiling and Wall Installation ..............................................................................................................................- 6 -  
Adjustable Height ...............................................................................................................................................- 7 -  
Adjustments and Extension Arm ........................................................................................................................- 8 -  
Mount Installation...............................................................................................................................................- 9 -  
Troubleshooting Procedures .............................................................................................................................- 11 -  
Technical Specifications...................................................................................................................................- 12 -  
Warranty ...........................................................................................................................................................- 13 -  
Contact InFocus Corporation............................................................................................................................- 13 -  
Notes .................................................................................................................................................................- 14 -  
Installation Manual  
Page - 3 -  
 
SP-CEIL-012  
Warning Statements  
THE CEILING STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE (5) TIMES  
THE WEIGHT OF THE PROJECTOR. IF NOT, THE CEILING MUST BE REINFORCED. PROPER  
INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN THE  
INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT  
IN SERIOUS PERSONAL INJURY, OR EVEN DEATH.  
WARNING:  
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF  
THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION  
PROCEDURE TO PREVENT PERSONAL INJURY.  
WARNING:  
WARNING:  
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS  
SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE INSTALLATION INSTRUCTIONS  
MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE. KEEP THESE  
INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE  
REFERENCE.  
Indicates that the power plug is to be  
disconnected from the power outlet.  
Contact InFocus Corporation with any  
questions.  
Safety precautions must be taken at all  
times.  
Warning and Caution statements.  
A secure structure must support the weight, or load, of the projector. When mounting to a ceiling  
that contains wooden studs, dead center of the wooden stud must be confirmed prior to  
installation.  
Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to  
do so could result in damage to the projector and/or damage to the mounting surface.  
Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of direct  
heat energy. Failure to do so may result in damage to the projector and could increase the risk of  
fire.  
At least two qualified people should perform the installation procedure. Injury and/or damage can  
result from dropping or mishandling the projector.  
Recommended mounting surfaces: wooden studs and solid-flat concrete. If the mount is to be  
installed on any surface other than wooden studs, use suitable hardware (which is commercially  
available).  
Page - 4 -  
Installation Manual  
 
SP-CEIL-012  
Parts List  
NOTE:  
This mount is shipped with all proper installation hardware and components. Make sure that none  
of these parts are missing and/or damaged before beginning installation. If there are parts missing  
and/or damaged, please stop the installation and contact InFocus Corporation (800-294-6400).  
SP-CEIL-012  
Ceiling Bracket  
(Qty 1)  
PBM-757 (Qty 1)  
PBB-10RL Base  
Box (Qty 1)  
M6 x 12mm Hinge  
Pin Screws (Qty 2)  
M6 x 12mm  
Phillips Head  
Screws (Qty 3)  
Flat Washers (Qty 2)  
M6 x 12mm  
Angle Locking  
Screws (Qty 2)  
Conical Spacers  
(Qty 2)  
#14 Wood  
Screws (Qty 2)  
M5 Set Screw (1ea)  
Installation Tools  
Phillips Head Screw Driver  
Soft Material/ Blanket  
1/8” Drill Bit  
Portable Drill  
Pencil  
Level  
Tape Measure  
M5 Allen Wrench  
Ladder  
Installation Manual  
Page - 5 -  
 
SP-CEIL-012  
Ceiling and Wall Installation  
Unpack the Gyrolock® and review any WARNING statements that apply to the installation. Select the desired  
location for the Gyrolock®. There are three mounting points for a single stud installation and four mounting  
points for a solid structure installation.  
NOTE:  
Pre-drill all holes (pilot hole – 1/8” drill bit).  
Single Stud Installation  
1. Locate the center of the single stud where the Gyrolock® will be installed. The two (2) center mounting  
points for this installation must be used. Use a stud finder to locate the stud that will be used to mount  
the PBL (ceiling or wall). It is advised that all holes be pre-drilled with a 1/8” drill bit.  
2. Secure the upper plate to the single stud with the two (2) #14 wood screws (supplied).  
3. Start to secure the plate to the outer mounting points first. The plate may travel ½" front to back from  
center.  
4. Secure the final wood screw to the center of the upper plate (Figure 1).  
SINGLE STUD  
Figure 1. Single Stud Installation  
Page - 6 -  
Installation Manual  
 
SP-CEIL-012  
Adjustable Height  
1. Screw the fully threaded nipple all the way into the secured top plate. Use the jam screw (supplied) to  
secure the pipe (Figure 2).  
2. Screw the PBC coupling all the way onto the threaded nipple or (optional) 1-1/2" pipe and secure the M6  
x 12 Phillip screw (Figure 3).  
CEILING STRUCTURE  
CEILING STRUCTURE  
TOP PLATE  
JAM NUT  
TOP PLATE  
JAM NUT  
(OPTIONAL LENGTH)  
1-1/2 NIPPLE  
1-1/2 NIPPLE  
Figure 2. Height Adjustment  
Figure 3. PBL Positioning  
Make sure you don’t remove the two (2) 8mm screws completely from the extension column  
when adjusting the height. Failure to do so may result in personal injury and damage to the  
projector. Simply loosen, adjust and tighten screws.  
WARNING:  
Installation Manual  
Page - 7 -  
 
SP-CEIL-012  
Adjustments and Extension Arm  
SP-EXTARM-01  
SP-EXTARM-02  
SP-EXTARM-03  
SP-EXTARM-04  
Contact InFocus for extensions.  
Adjustments  
Roll & pitch greater than ± 20° from center.  
Quick positive release with positive security lock.  
360° yaw.  
Cables can be routed inside the adjustable column of 1.5” piping.  
TOP PLATE  
JAM NUT  
(OPTIONAL)  
1-1/2 (NTP) PIPE  
Figure 4. Extensions Pipe (Optional)  
Page - 8 -  
Installation Manual  
 
SP-CEIL-012  
Mount Installation  
1. Invert the projector and place it on a soft and flat  
surface. Locate the three (3) 6 (mm) mounting  
points found on the bottom of the projector.  
2. Secure the mounting bracket using the three (3) 6  
(mm) x 12 (mm) Phillip Head screws (supplied).  
3. Do not over tighten the screws!  
Figure 5  
1. Install the base box securely to the ceiling  
structure in accordance with proper commercial  
standards. Use (commercially available) suitable  
hardware depending on the installation  
requirements.  
NOTE:  
If an extension adapter is to be used,  
InFocus has a variety of different  
adapters that can be purchased. Please  
contact Customer Service.  
Figure 6  
Installation Manual  
Page - 9 -  
 
SP-CEIL-012  
1. Install the two (2) conical spacers and two (2)  
flat washers two, (2) hinge pin screws loosely  
on both sides of the base box.  
2. Raise the projector with the mounting bracket  
attached and slip though the hinge pin slots  
openings on the bracket into the base box.  
3. Install the two (2) angle locking screws adjust  
the angle, lock it, and then tighten the hinge  
pin screws.  
Figure 7  
1. Check all the hardware for proper tightness and  
security. Do not over tighten hardware.  
1. Install the two (2) conical spacers and two (2)  
flat washers, two (2) hinge pin screws loosely  
on both sides of the base box.  
2. Raise the projector with the mounting bracket  
attached and slip though the hinge pin slots  
openings on the bracket into the base box.  
3. Install the two (2) angle locking screws adjust  
the angle, lock it, and then tighten the hinge  
pin screws.  
Figure 8  
Page - 10 -  
Installation Manual  
 
SP-CEIL-012  
Troubleshooting Procedures  
QUESTION:  
My projector mount must be set at an angle to be viewed properly on the wall, but the  
projector will not hold at this position. Why is this?  
ANSWER:  
The angle adjustments are not tight; they must be tightened.  
QUESTION:  
Why won’t my bracket fit my projector?  
ANSWER:  
There may be several mounting positions for your particular bracket. Try to line up the  
holes on the bracket with the mounting points on the projector. If this still does not  
solve the problem, then contact Customer Service and advise them of the situation.  
Installation Manual  
Page - 11 -  
 
SP-CEIL-012  
Technical Specifications  
6.00  
4.50 6.75  
4.50  
Figure 5. Technical Dimensions  
Page - 12 -  
Installation Manual  
 
SP-CEIL-012  
Warranty  
Limited Lifetime Warranty  
All products carry a limited lifetime warranty from ship date against defects in materials and workmanship.  
InFocus Corporation is not liable for improper installation that results in damage to mounts, adapters, display  
equipment or personal injury.  
Contact InFocus Corporation  
In the event of missing and/or damaged equipment, or technical questions, the following information can  
help in the completion of the installation.  
Customer Service – (800) 294-6400  
Installation Manual  
Page - 13 -  
 
SP-CEIL-012  
Notes  
InFocus Corporation  
27700B S.W. Parkway Ave.  
Wilsonville, OR 97070-9215  
1-800-294-6400  
Page - 14 -  
Installation Manual  
IN-SPECEIL012.R2  
 

Indesit Double Oven FID20WH User Manual
Intellinet Network Solutions Network Router 524827 User Manual
Invacare Mobility Aid 1487 User Manual
Invacare Mobility Aid 1130213 User Manual
JBL Speaker L226C User Manual
Jensen Car Video System VM9411 User Manual
John Deere Snow Blower MTF 031039C User Manual
JVC Headphones HA FX67 User Manual
KitchenAid Convection Oven KERA205PBL1 User Manual
KitchenAid Toaster 4KPTT780ER1 User Manual